«PeakTech® P 6227» Switching Mode Power Supply 0 - 60 V / 0 - 6 A DC

€119.90*

Prices excl. VAT plus shipping costs and possibly lower value surcharge

PDF Datasheet

Product number: P 6227

EAN: 4250569404924

Downloads

Product information "«PeakTech® P 6227» Switching Mode Power Supply 0 - 60 V / 0 - 6 A DC"

This newly developed laboratory power supply offers a controllable 0...60V or 0...6A DC main output with a maximum continuous power of 150W. For developers, this laboratory power supply offers two switchable USB outputs with their own LCD display for the voltage and current values. If you use a load up to 2.5A, you can set the output voltage up to 60V. If you want to use a higher current up to 6A, set the load to a maximum of 25V. Of course, all stages are also adjustable in between, e.g. 30V/5A, 40V/3.7A or 50V/3A. The current and voltage setting also can be done when the output is switched off. By pressing the knob for current or voltage, the setting resolution can be fine/coarse switched from 1mA to 100mA or 10mV to 1V. Due to the high range of functions and the simple operation with the best price-performance ratio, this laboratory power supply is ideal for the education, hobby, development and service sector.

USB:	■ (Power Only)
Channels:	1 CH
Display Type:	LCD
Input connector:	IEC socket
Input voltage:	100 - 240 VAC 50/60 Hz
Output Connection:	4 mm Buchse
Output Current:	0 - 6 A
Output Voltage:	0 - 60 V DC
Remote Control:	□

Blue LCD display showing the output voltage and current values
Green LCD display showing the USB output voltage and current values
150W constant output power
Adjustable voltage range: 0~60V at 0~2.5A and 0~25V at 2.5~6A
Voltage and current pre-selection with switchable output
C.C. (Constant Current) and C.V. (Constant Voltage) mode with connected load
Protection against short circuit, overload and overtemperature
Safety: EN 61010-1
Accessories: Power cable, Connection Leads and manual

Zubehör / Accessories:

«PeakTech® P 8201» Measuring Accessories Set with 4mm Plugs

The PeakTech 8201 accessory set was specially put together for the training and laboratory area and includes a practical collection of 4 mm cables with banana plugs, test probes and connection terminals which are ideal for connecting electronic loads and laboratory power supplies. The double-insulated plastic parts are made of flexible and durable material.

€49.90*

«PeakTech® P 8202» Set of laboratory cables with 4mm banana plugs

These high-quality connection cables with 4mm banana plugs are the perfect addition for use with laboratory power supplies in the SELV/PELV range. The robust banana plugs fit into all standard 4mm sockets and enable a secure and reliable connection. The coupling socket on the rear allows an additional cable with a 4mm plug to be inserted, which increases flexibility and application versatility. The set consists of four colour-coded cables in red, black, blue and yellow, ensuring easy assignment and clarity. These connection cables not only offer excellent conductivity and durability, but are also easy to handle and versatile. They are ideal for professional use in the laboratory, but are also a valuable aid for the ambitious hobby electronics engineer. This comprehensive set is sufficient for a complete laboratory workstation and contains a total of 24 laboratory cables - 4 cables each of 25cm, 50cm, 75cm, 100cm, 150cm and 200cm.

€49.90*

«PeakTech® P 8200» Measuring Accessories Set

This extensive collection of test accessories for the electronics area provides the best suitable measuring adapter for the desired application for each digital multimeter. In addition, these high quality clips and cables are all manufactured to the latest safety standards and provides a high safety in every application for the user. For the material, a flexible plastic was chosen, which can also withstand the hardest kinds of usage.

€45.90*

«PeakTech® P 7000» Tapping clamps for Digital Multimeter up to 10 A

These measuring accessories with 4 mm sockets can be connected to almost all measuring devices. Thanks to its hook-shaped alligator clips, it is possible to carry out measurements even in hard-to-reach points on a circuit. A maximum of safety is achieved by the double insulation of the lines and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€16.70*

«PeakTech® P 7051» Set of 4 Test Leads (200cm) for Laboratory Power Supplies

Set of four connecting cables with 4mm banana plugs for laboratory power supplies and experimental setups in red, black, blue, and yellow. Suitable for low voltages below 50 VAC and 120 VDC up to a maximum of 10A.

€13.00*

«PeakTech® P 7050» Set of 4 Test Leads (150cm) for Laboratory Power Supplies

€12.00*

«PeakTech® P 7048» Set of 4 Test Leads (75cm) for Laboratory Power Supplies

€10.00*

«PeakTech® P 7005» Test Leads for Digital Multimeter with extension

This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. With the extension adapters, it is possible to connect the test leads to other test leads in order to carry out measurements over long distances. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€8.90*

«PeakTech® P 7015» Alligator clamps for Digital Multimeter

The alligator clips enable safe measurements even on bare or exposed cables. With their 4 mm sockets, they can be used for almost any multimeter and measuring device. A maximum of safety is achieved by the protection against against accidental contact with conductive metal parts. This makes these accessories ideal for use in training and service.

€8.90*

«PeakTech® P 7047» Set of 4 Test Leads (50cm) for Laboratory Power Supplies

€8.00*

«PeakTech® NK / UK-ST» IEC connection cable, length: 1.8m, UK plug, 250 V / 60 Hz; 5 A

Connection cable for devices with UK plug

€7.90*

«PeakTech® NK / US-ST» device connection cable according to US standard, type Feller 498 G / C13, 125 V AC / 10A

Connection cable for devices with US plug

€7.90*

«PeakTech® P 7046» Set of 4 Test Leads (25cm) for Laboratory Power Supplies

€7.00*

«PeakTech® P 7020» Test Leads for Digital Multimeter

This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. A maximum of safety is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€6.90*

«PeakTech® P 7025» Test Leads for Digital Multimeter with coupling

These test leads with 4 mm sockets have a coupling, which makes it possible to connect other test leads to them. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€6.90*

«PeakTech® NK / EU-ST» IEC connection cable Length: 1.5m black 10-16 A / 250 V

Connection cable for devices with EU plug

€4.90*

«PeakTech® P 7049 BLACK» Testkabel 100 cm (Farbe: schwarz)

Set of 10 connecting cables with 4mm banana plugs for laboratory power supplies and experimental setups. These cables are black. Suitable for low voltages below 50 VAC and 120 VDC up to a maximum of 10A.

€2.75*