«PeakTech® P 6300» Symmetrical DC Power Supply, 30 V DC max.

€179.90*

Prices excl. VAT plus shipping costs and possibly lower value surcharge

PDF Datasheet

Product number: P 6300

EAN: 4250569403583

Downloads

Product information "«PeakTech® P 6300» Symmetrical DC Power Supply, 30 V DC max."

This laboratory power supply for symmetrical output voltage has a stepless voltage regulation. There are three output sockets on the front panel, the middle socket is acting as a center tap (0). A voltage of - 15 to 0V DC can be released from the center tap to the negative socket or a voltage of 0 - 15V DC to the positive socket. If the load is connected between the positive and negative pole, it can be released up to 30 V DC. This device also has a 5 V / 0.5 A DC fixed voltage output. As a result, this device is ideally suited for use in the training area and it is useful for explaining polarity in the DC area.

Auxillary output:	5 V DC
Channels:	1 CH
Cooling:	Active
Display Type:	Segment
Input voltage:	230 VAC / 50 Hz
Output Current:	0 - 1,5 A
Output Voltage:	+/- 15 V DC
SELV:	■

3-digit, blue LED display
Variable voltage setting
Automatic overcurrent limitation
High load stability and low ripple
Robust metal housing with carrying handle
Safety EN-61010-1
Safety-Transformer: EN 61558 - 2 - 6
Accessories: Power cord and manual

Zubehör / Accessories:

«PeakTech® NK / EU-ST» IEC connection cable Length: 1.5m black 10-16 A / 250 V

Connection cable for devices with EU plug

€4.90*

«PeakTech® NK / UK-ST» IEC connection cable, length: 1.8m, UK plug, 250 V / 60 Hz; 5 A

Connection cable for devices with UK plug

€7.90*

«PeakTech® NK / US-ST» device connection cable according to US standard, type Feller 498 G / C13, 125 V AC / 10A

Connection cable for devices with US plug

€7.90*

«PeakTech® P 7000» Tapping clamps for Digital Multimeter up to 10 A

These measuring accessories with 4 mm sockets can be connected to almost all measuring devices. Thanks to its hook-shaped alligator clips, it is possible to carry out measurements even in hard-to-reach points on a circuit. A maximum of safety is achieved by the double insulation of the lines and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€16.70*

«PeakTech® P 7005» Test Leads for Digital Multimeter with extension

This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. With the extension adapters, it is possible to connect the test leads to other test leads in order to carry out measurements over long distances. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€8.90*

«PeakTech® P 7015» Alligator clamps for Digital Multimeter

The alligator clips enable safe measurements even on bare or exposed cables. With their 4 mm sockets, they can be used for almost any multimeter and measuring device. A maximum of safety is achieved by the protection against against accidental contact with conductive metal parts. This makes these accessories ideal for use in training and service.

€8.90*

«PeakTech® P 7020» Test Leads for Digital Multimeter

This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. A maximum of safety is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€6.90*

«PeakTech® P 7025» Test Leads for Digital Multimeter with coupling

These test leads with 4 mm sockets have a coupling, which makes it possible to connect other test leads to them. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€6.90*

«PeakTech® P 7046» Set of 4 Test Leads (25cm) for Laboratory Power Supplies

Set of four connecting cables with 4mm banana plugs for laboratory power supplies and experimental setups in red, black, blue, and yellow. Suitable for low voltages below 50 VAC and 120 VDC up to a maximum of 10A.

€7.00*

«PeakTech® P 7047» Set of 4 50cm Test Leads for Laboratory Power Supplies

€8.00*

«PeakTech® P 7048» Set of 4 Test Leads (75cm) for Laboratory Power Supplies

€10.00*

«PeakTech® P 7049 BLACK» Testkabel 100 cm (Farbe: schwarz)

Set of 10 connecting cables with 4mm banana plugs for laboratory power supplies and experimental setups. These cables are black. Suitable for low voltages below 50 VAC and 120 VDC up to a maximum of 10A.

€2.75*

«PeakTech® P 7050» Set of 4 Test Cables, 150cm, for Laboratory Power Supplies

€12.00*

«PeakTech® P 7051» Set of 4 Test Cables, 200cm, for Laboratory Power Supplies

€13.00*

«PeakTech® P 8200» Measuring Accessories Set

This extensive collection of test accessories for the electronics area provides the best suitable measuring adapter for the desired application for each digital multimeter. In addition, these high quality clips and cables are all manufactured to the latest safety standards and provides a high safety in every application for the user. For the material, a flexible plastic was chosen, which can also withstand the hardest kinds of usage.

€45.90*

«PeakTech® P 8201» Measuring Accessories Set with 4mm Plugs

The PeakTech 8201 accessory set was specially put together for the training and laboratory area and includes a practical collection of 4 mm cables with banana plugs, test probes and connection terminals which are ideal for connecting electronic loads and laboratory power supplies. The double-insulated plastic parts are made of flexible and durable material.

€49.90*

«PeakTech® P 8202» Set of laboratory cables with 4mm banana plugs

These high-quality connection cables with 4mm banana plugs are the perfect addition for use with laboratory power supplies in the SELV/PELV range. The robust banana plugs fit into all standard 4mm sockets and enable a secure and reliable connection. The coupling socket on the rear allows an additional cable with a 4mm plug to be inserted, which increases flexibility and application versatility. The set consists of four colour-coded cables in red, black, blue and yellow, ensuring easy assignment and clarity. These connection cables not only offer excellent conductivity and durability, but are also easy to handle and versatile. They are ideal for professional use in the laboratory, but are also a valuable aid for the ambitious hobby electronics engineer. This comprehensive set is sufficient for a complete laboratory workstation and contains a total of 24 laboratory cables - 4 cables each of 25cm, 50cm, 75cm, 100cm, 150cm and 200cm.

€49.90*