innovative
progressive
reliable

«PeakTech® P 3385» Analog multimeter, 600V AC/DC, 10A AC/DC, CAT III

€31.40*

PDF Datasheet
Product number: P 3385
EAN: 4250569400896
Product information "«PeakTech® P 3385» Analog multimeter, 600V AC/DC, 10A AC/DC, CAT III"
This analog multimeter has a variety of measurement functions, such as the measurement of AC and DC voltage, direct and alternating current or resistance measurement with an acoustic continuity tester. Due to the analog technology, batteries are only required for functions such as resistance measurement, in which the multimeter has to output a test voltage. The voltage and current measurement, on the other hand, does not require any voltage from the batteries. Special protection is provided by the housing, which is provided with a sprayed-on rubber coating and is protected against falling damage. User safety is also guaranteed via the CAT III 600V overvoltage category.
Display Type: Analog
Over voltage category: CAT III 600 V
V DC max.: 600V
A AC max.: 10A
OHM max.: 2 MΩ
mA DC max.: 500mA
V AC max.: 600 V
A DC max.: 10A
mA AC max.: 500 mA
  • 20 measuring ranges; 75 mm mirror scale
  • Input resistance: 20 kΩ / V DC - 9 kΩ / V AC
  • Continuity test with acoustic signal
  • Safety: EN 61010-1; CAT III 600 V
  • Accessories: bag, test leads, batteries and manual
«PeakTech® MKS-10» Measuring tip set with 1 mm test tips
This measuring tip set for all standard measuring lines with 4 mm safety sockets was developed in order to be able to measure even small components precisely. This measuring tip set also includes the matching alligator clips, that it is possible to fix the measuring tips to the component to be measured. When using the measuring tips without the alligator clips, an overvoltage category of CAT I 1000 V is guaranteed. By using the alligator clips, it is possible to use the overvoltage category CAT III.

€9.95*

«PeakTech® P 7000» Tapping clamps for Digital Multimeter up to 10 A
These measuring accessories with 4 mm sockets can be connected to almost all measuring devices. Thanks to its hook-shaped alligator clips, it is possible to carry out measurements even in hard-to-reach points on a circuit. A maximum of safety is achieved by the double insulation of the lines and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€15.60*

«PeakTech® P 7005» Test Leads for Digital Multimeter with extension
This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. With the extension adapters, it is possible to connect the test leads to other test leads in order to carry out measurements over long distances. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€8.30*

«PeakTech® P 7010» Tapping clamps for Digital Multimeter; 5 A
This measuring accessory with 4 mm sockets can be connected to almost all measuring devices and power supplies. Thanks to the fine alligator clips, even measurements on small components or at hard-to-reach points on circuits are possible. A maximum of security is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€7.20*

«PeakTech® P 7015» Alligator clamps for Digital Multimeter
The alligator clips enable safe measurements even on bare or exposed cables. With their 4 mm sockets, they can be used for almost any multimeter and measuring device. A maximum of safety is achieved by the protection against against accidental contact with conductive metal parts. This makes these accessories ideal for use in training and service.

€8.30*

«PeakTech® P 7020» Test Leads for Digital Multimeter
This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. A maximum of safety is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€5.10*

«PeakTech® P 7025» Test Leads for Digital Multimeter with coupling
These test leads with 4 mm sockets have a coupling, which makes it possible to connect other test leads to them. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€5.10*

«PeakTech® P 8200» Measuring Accessories Set
This extensive collection of test accessories for the electronics area provides the best suitable measuring adapter for the desired application for each digital multimeter. In addition, these high quality clips and cables are all manufactured to the latest safety standards and provides a high safety in every application for the user. For the material, a flexible plastic was chosen, which can also withstand the hardest kinds of usage.

€41.90*

«PeakTech® TKS-2» Test Leads with 2 mm probe tip
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The test probes length of the TKS-2 cables are limited to 2mm for the best possible user safety when used in CAT III and CAT IV environments.

€4.10*

«PeakTech® TKS-4» Test Leads with 4 mm spring-contact probe tip
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The 4mm diameter spring contact test probes of the TKS-4 cables fit exactly into power sockets and are provided with removable protective caps. In CAT I / CAT II measurement environments, these can be accepted for a probe tip length of 18mm, in CAT III / CAT IV measurement environments they must remain attached for better user safety and provide a probe tip length of 4mm.

€7.20*

«PeakTech® TKS-5» Testkabelsatz für Digital-Multimeter, PeakTech 3355/3360, TKS-5
Dieser Testkabelsatz für Multimeter besteht Sicherheitsprüfleitungen entsprechend der Norm EN 61010-031 mit 4 mm Sicherheitsbuchsen in robuster Bauform mit einer Kabellänge von 120 cm und 90° Winkelstecker. Die 2mm Durchmesser Prüfspitzen der TKS-5 Leitungen sind mit abnehmbaren Schutzkappen versehen. In CAT I / CAT II Messunmebungen können diese für eine Prüfspitzenlänge von 18mm abgenommen werden, in CAT III / CAT IV Messumgebungen müssen diese für eine bessere Anwendersicherheit aufgesteckt bleiben und stellen eine Prüfspitzenlänge von 4mm zur Verfügung.Diese Prüfleitungen besitzen einen anderen 4 mm Stecker mit Dichtring, da diese Prüfleitungen speziell für wasserdichte Multimeter (P 3355, P 3360, P 3443, P 3444, P 3445) geeignet sind.

€4.20*

«PeakTech® TKS-8» Test Leads with 2 mm probe tip and sleeves
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The 2mm diameter test probes of the TKS-8 cables are provided with removable protective caps. In CAT I / CAT II measurement environments, these can be accepted for a probe tip length of 18mm, in CAT III / CAT IV measurement environments they must remain attached for better user safety and provide a probe tip length of 4mm.

€7.20*

«PeakTech® P 7501» microfuse ~ 0.5 A / 690 V ~ 10.3 x 38 mm ~ super fast (FF)
This modern device protection fuse with ceramic body offers a much higher protection against damage to the measuring device when triggered than conventional glass fuses. Due to the larger design, a voltage flashover between the internal fuse holders of modern measuring devices can be effectively prevented, even with high test current voltages. Triggered fuses may only be replaced with replacement fuses of the same design and specifications in order to guarantee the safety of the device and thus also the safety of the user for future measurements.

€2.19*

«PeakTech® P 7525» microfuse ~ 10 A / 690 V ~ 10.3 x 38 mm ~ super fast acting (FF)
Modern device fuses with ceramic bodies offer a significantly higher level of protection against damage to the measuring device when triggered than conventional glass fuses. Due to the larger design, a voltage flashover between the internal fuse holders of modern measuring devices can be effectively prevented even with high test current voltages. Triggered fuses may only be replaced with replacement fuses of the same design and specifications in order to guarantee the safety of the device and thus also the safety of the user in future measurements.

€2.19*