innovative
progressive
reliable

«PeakTech® P 1610» Clamp meter 4,000 counts 1000 A AC

€59.90*

PDF Datasheet
Product number: P 1610
EAN: 4250569400308
Product information "«PeakTech® P 1610» Clamp meter 4,000 counts 1000 A AC"
The PeakTech 1610 is a measuring device for AC alternating currents up to 1000 A via a current clamp for cable diameters up to 35mm. Current clamps are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly. In addition, this model has extensive multimeter functions for voltage, resistance, frequency, capacitance and temperature measurement. Continuity tests with acoustic signals and diode tests can also be carried out. Due to its high functionality and simple handling, this current clamp is suitable for electronics specialists, service technicians or hobbyists.
Capacitance max.: 100 µF
Digital counts: 4.000
Display Type: LCD
Over voltage category: CAT III 600 V
TÜV/GS:
V DC max.: 600V
A AC max.: 1000 A
Hz max.: 10 MHz
OHM max.: 40 MΩ
Temp. max.: 1000 °C
Temp. min.: -50 °C
mV DC max.: 400 mV
V AC max.: 600 V
mV AC max.: 400 mV
  • Suitable for AC current measurements up to 1000 A.
  • LCD display with 4000 digits and backlight
  • Voltage measurements up to 600 V AC / DC
  • Resistance measurement, continuity tester and diode test
  • Frequency measurement and Hz / duty function
  • Capacitance measurement function up to 100 µF
  • Temperature measuring function with enclosed wire sensor
  • Data hold function, automatic and manual range selection
  • Conductor diameter up to max. 35 mm
  • Safety: TÜV / GS, EN 61010-1, CAT III 600 V
  • Accessories: temperature sensor and adapter, carrying case, test leads, battery and manual
«PeakTech® P 8200» Measuring Accessories Set
This extensive collection of test accessories for the electronics area provides the best suitable measuring adapter for the desired application for each digital multimeter. In addition, these high quality clips and cables are all manufactured to the latest safety standards and provides a high safety in every application for the user. For the material, a flexible plastic was chosen, which can also withstand the hardest kinds of usage.

€41.90*

«PeakTech® P 7000» Tapping clamps for Digital Multimeter up to 10 A
These measuring accessories with 4 mm sockets can be connected to almost all measuring devices. Thanks to its hook-shaped alligator clips, it is possible to carry out measurements even in hard-to-reach points on a circuit. A maximum of safety is achieved by the double insulation of the lines and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€15.60*

«PeakTech® MKS-10» Measuring tip set with 1 mm test tips
This measuring tip set for all standard measuring lines with 4 mm safety sockets was developed in order to be able to measure even small components precisely. This measuring tip set also includes the matching alligator clips, that it is possible to fix the measuring tips to the component to be measured. When using the measuring tips without the alligator clips, an overvoltage category of CAT I 1000 V is guaranteed. By using the alligator clips, it is possible to use the overvoltage category CAT III.

€9.95*

«PeakTech® P 7005» Test Leads for Digital Multimeter with extension
This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. With the extension adapters, it is possible to connect the test leads to other test leads in order to carry out measurements over long distances. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€8.30*

«PeakTech® P 7015» Alligator clamps for Digital Multimeter
The alligator clips enable safe measurements even on bare or exposed cables. With their 4 mm sockets, they can be used for almost any multimeter and measuring device. A maximum of safety is achieved by the protection against against accidental contact with conductive metal parts. This makes these accessories ideal for use in training and service.

€8.30*

«PeakTech® TKS-4» Test Leads with 4 mm spring-contact probe tip
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The 4mm diameter spring contact test probes of the TKS-4 cables fit exactly into power sockets and are provided with removable protective caps. In CAT I / CAT II measurement environments, these can be accepted for a probe tip length of 18mm, in CAT III / CAT IV measurement environments they must remain attached for better user safety and provide a probe tip length of 4mm.

€7.20*

«PeakTech® P 7010» Tapping clamps for Digital Multimeter; 5 A
This measuring accessory with 4 mm sockets can be connected to almost all measuring devices and power supplies. Thanks to the fine alligator clips, even measurements on small components or at hard-to-reach points on circuits are possible. A maximum of security is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€7.20*

«PeakTech® TKS-8» Test Leads with 2 mm probe tip and sleeves
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The 2mm diameter test probes of the TKS-8 cables are provided with removable protective caps. In CAT I / CAT II measurement environments, these can be accepted for a probe tip length of 18mm, in CAT III / CAT IV measurement environments they must remain attached for better user safety and provide a probe tip length of 4mm.

€7.20*

«PeakTech® P 7020» Test Leads for Digital Multimeter
This measuring accessorie with 4 mm sockets can be connected to almost all measuring devices and power supplies. A maximum of safety is achieved by the double insulation of the wires and the protection against accidental contact with conductive metal parts when closed. This makes these accessories ideal for use in training and service.

€5.10*

«PeakTech® P 7025» Test Leads for Digital Multimeter with coupling
These test leads with 4 mm sockets have a coupling, which makes it possible to connect other test leads to them. The safety of these measuring wires is ensured by the double insulation of the lines and the contact protection against conductive metal parts. This makes these accessories ideal for use in training and service.

€5.10*

«PeakTech® TKS-5» Testkabelsatz für Digital-Multimeter, PeakTech 3355/3360, TKS-5
Dieser Testkabelsatz für Multimeter besteht Sicherheitsprüfleitungen entsprechend der Norm EN 61010-031 mit 4 mm Sicherheitsbuchsen in robuster Bauform mit einer Kabellänge von 120 cm und 90° Winkelstecker. Die 2mm Durchmesser Prüfspitzen der TKS-5 Leitungen sind mit abnehmbaren Schutzkappen versehen. In CAT I / CAT II Messunmebungen können diese für eine Prüfspitzenlänge von 18mm abgenommen werden, in CAT III / CAT IV Messumgebungen müssen diese für eine bessere Anwendersicherheit aufgesteckt bleiben und stellen eine Prüfspitzenlänge von 4mm zur Verfügung.Diese Prüfleitungen besitzen einen anderen 4 mm Stecker mit Dichtring, da diese Prüfleitungen speziell für wasserdichte Multimeter (P 3355, P 3360, P 3443, P 3444, P 3445) geeignet sind.

€4.20*

«PeakTech® TKS-2» Test Leads with 2 mm probe tip
This test cable set for multimeters consists of safety test leads in accordance with the EN 61010-031 standard with 4 mm safety sockets in a robust design with a cable length of 120 cm and 90 ° angled plugs. The test probes length of the TKS-2 cables are limited to 2mm for the best possible user safety when used in CAT III and CAT IV environments.

€4.10*